home Success stories DIY iron figurines. Simple DIY metal crafts for sale

DIY iron figurines. Simple DIY metal crafts for sale

First products - metal crafts were made in ancient times by skilled craftsmen. Gradually artistic forging turned into a real work of art and, starting from the 11th century, became an integral part of the architectural structures of Europe. Today metal products have high cost, but at the same time they can emphasize the exclusivity of the exterior or interior of an apartment or country house. We offer you several master classes that will help you make metal crafts with your own hands.

Metal owl

Materials:

Let's start making metal crafts - an owl

1) Using a pencil on a sheet of paper, draw an owl.

2) We visually break the owl into separate elements and transfer them to sheets of cardboard to make the owl life-size. Cut out the templates with scissors.

3) Now we apply the cardboard templates to the sheet metal, transfer them and carefully cut out each detail of the owl with a grinder.

4) In the part that is the eyes of the owl, we make holes for the bolts. We make them using a chisel and a hammer.

5) Now we make feathers on all the parts of the owl. To do this, take a chisel and make notches.

6) Paws are easy to make from a rod. We cut off the pieces needed for the paws from the rod and weld them together to form a paw. We do the second one in the same way.

7) Make a beak from a piece of sheet metal.

9) Now you can connect the parts into one whole. To do this, carefully weld each of them to each other in the required sequence on the back side of the owl. Then we weld the beak and paws to the finished owl.

10) Now, using a chemical solvent, we clean the owl from rust. Follow the instructions on the solvent. If you don't have a suitable solvent, make a solution of baking soda and water at home. It should be so thick that it spreads easily over the surface. Clean the owl with an old toothbrush, and then rinse thoroughly. It is recommended to do all work with solvents with gloves.

11) When the cleaning process is completed, cover the entire owl with a special varnish. It can be purchased at a special store.

Metal owl craft ready. It will become creative, made with love and skill, and will keep memories of the master forever.

Metal figurines look original in a flowerbed or in a garden at their summer cottage, so with the help of our step by step instructions you can easily make a rat or some other animal out of metal.

Material:

Bulgarian;
drill with metal drill bit;
metal scissors;
electric welding;
grinding circle for grinder;
rods with a diameter of 4,6,10,12 and 14 mm;
2 mm metal sheet;
wire;
metal ball from the bearing 3 pieces.

1) Take two pieces of metal pipe (this rat is 50 centimeters high). We make a head from one of them: we cut out identical segments along the entire diameter and get a blank, as in the photo. Then we weld and, using a grinder with a cleaning wheel, clean this part. We make the body and also clean it in a similar way. Consider the proportions: the head is larger than the body. We weld the head to the body.

2) Transfer sketches of the rat’s ears and paws onto a 2 mm sheet of metal and cut them out. We roll the paw blanks into a funnel. We scald them and clean the seams. Then we electric weld each leg to the body and clean the seams again. We weld the ears to the head and don’t forget to clean the seams too.

3) Now we make the rat’s paws and hands from twigs. For the upper legs, a 4 mm rod is welded to 10 mm, and for the lower 6 mm legs, it is welded to 12 mm. We insert it into the holes of the funnels and scald it with welding.

4) We make the tail from a 14 mm rod and weld it to the body.

5) Let's move on to the rat's face. First, let's make two holes in the head for the eyes. They should be smaller than the bearing balls. Now let's drown these balls in the holes and weld them neatly and thinly. We electric weld the remaining ball in place of the nose. Drill holes for the wire whiskers and insert it.

7) Then we make longitudinal welds close to each other throughout the rat. This will create an imitation of wool. Now we clean the whole craft again using a grinder with the required disk. This is necessary in order to rid the product of scale, slag and add shine.

8) At the end of the work, we apply a special varnish to the metal rat, it can be colorless, or it can have some effect. It's up to you. The rat in the photo is coated with colorless varnish with a satin effect.

Now all that’s left is to figure out where to put it or who to give such a wonderful gift to.

Rose- This is a unique flower, the beauty of which I would like to preserve for as long as possible. Metal rose will delight you for many years and will decorate the classic bedroom interior.

Materials and tools:

Master class metal rose

1) During work, follow safety precautions, use gloves and a welding mask.

2) Using special scissors, cut out petals for a bud and a couple of leaves for a rose from sheet metal. We cut out the petals in the following sequence: from smallest to largest, starting from 15 mm and ending with 80 mm. You need to cut about thirty petals, then the bud will be dense and full.

3) Then smooth the edges of each petal using a sharpening stone.

4) From the remaining scraps of sheet metal, cut out triangles - they will become rose thorns. Their size should not be less than 10 mm.

5) We make a stem blank from steel wire. Our task is to get rid of its flat state. To do this, we can use a hammer to bend it a little so that it looks like a real rose stem.

6) Create a bud. The first two smallest petals need to be clamped in a yew and bent in half. Next, we begin to form eight petals in an arc relative to the center of the bud, but be sure to grab each part by welding and then clean it.

7) All subsequent petals are also formed in an arc, but bending the top of the petal. We do this procedure with a hammer. And just like the previous petals, we weld them and clean them again.

8) Now we weld the thorns to the already prepared stem. Then we clean them with a grinder.

9) Rose leaves. You need to squeeze and release the leaf in a yew to create a vein. Then we bend the edges using pliers. Now we weld the leaves to the stem and clean the seams.

10) We weld the rose bud to its stem, carefully clean the joints and cover the entire rose with metal paint.

A beautiful flower that combines the tenderness of beauty and the rigidity of metal is ready. An original and such a painstaking gift will delight the female eye for many years.

Metal crafts: Panel - fish

Panel is a decorative composition that serves for beauty and comfort in the home. It can be a carved or ceramic composition, bas-relief or stucco. In the architecture of buildings there are often panels made of tiles of different colors or using the mural technique. We offer to make crafts from metal: a wall panel from a metal frame with your own hands.

Materials

1) The very first thing you need to do is draw a sketch of the fish that will occupy a central place in the panel.

2) Based on the sketch, we begin to make a fish frame from thick wire. At the same time, we make curves, as in the photo. In paragraph 5 you will understand what they are for.

3) From the same wire we make jumpers that will increase the rigidity of the structure.

4) Thin wire is needed to fix the frame.

5) Now we begin to fill the fish with beads and beads. To do this, we attach a thin wire to the curves on the frame and begin to string beads on it. So we braid all parts of the fish with beads, while securing the wire with the beads. To make the product look aesthetically pleasing, do this on the back side of the fish. The beads will help highlight the large scales of the fish, and one bead will be used to make the eye. The color of the future craft depends on the selected beads, so use your imagination and don’t be afraid.

The finished fish can be hung on the wall in the nursery or hallway. It will become not only an interior decoration, but also a pleasant gift for a fishing enthusiast. We recommend making several fish so that you can create a whole one on the wall.

Metal crafts parents can do it with the whole family, as they need to follow safety precautions when working with a welding machine. If you do not have special skills in working with metal, you can make a craft from wire or tin can, which will also look exclusive. This concludes our article about DIY metal crafts; see more crafts on the website.

It’s not difficult to create crafts for the garden made of metal using welding yourself, even if you are new to this business and have no experience at all. The main requirement is compliance

Metal products made by welding are very useful in private homes or country houses. Such designs will be well suited for the construction of a fence, gazebo, canopy and for all kinds of decorations of the area around the house.

The first thing you need to do before you start making crafts using the welding method is to get a good welding machine. In domestic and domestic conditions, unlike industrial ones, there are no strict requirements for the quality of connections. Therefore, in order to create iron crafts and metal products, you can use a transformer or inverter.

Both devices have both advantages and disadvantages.

A transformer is a device that is quite large in size. Such equipment weighs a lot, so welding takes a lot of effort and time, especially when the equipment needs to be moved over long distances. For example, if you are building a fence or other large items made of iron or metal. The next disadvantage is that electrical network subjected to heavy load.

The advantage of transformer equipment is that its design is simple, which means that assembly will not take much time.

Before you start making crafts with your own hands using welding, you need to familiarize yourself with the basics of welding work.

In the beginning, you need to gain experience and practice on a piece of unnecessary metal. At the initial stage of production welded joints, it is worth learning how to light an arc and hold it, while maintaining a constant working gap between the workpiece and the electrode.

The next thing you need to get your hands on is. Once you have gotten the hang of it and your seam is smooth, you can move on to adjusting the current for parts of different thicknesses to be welded.

Welding is a technique by which two metal parts are joined. The process consists of melting their surfaces at the joining point
The elements are welded into one whole structure thanks to a layer of electrode bonding material. The current must be selected in such a way that only the top layer of the product melts, otherwise holes may form.
Material
Surely every owner of a private house or cottage will have metal remains on his farm. For example, you were installing a gas pipeline, heating or water supply system, you had unused pipes lying around or just pieces of metal, pieces of fittings, nails, nuts, bolts, etc.
From all these seemingly unnecessary parts you can make excellent crafts that will find their application on your site.
Many users often use this material for repairs. Take a good look at your garage; perhaps there are old garden tools, dishes, or car or bicycle parts lying around. All this may also be useful to you.
Metal crafts for the garden
As already noted, you can make your site cozy and pleasing to the eye without purchasing new equipment. Using old metal or iron you can construct a good base for a bench or table. You can make a table top, a board for a bench, a swing and many other useful things for your garden.
If you like to spend your free time barbecuing, you can make a barbecue from an old steel barrel. It can be made disassembled so that it can be transported from one place to another. You can create it yourself using a grinder and a drill. However, the most the best option will be used welding machine. So, the process of creating a design will be faster and easier.
Sculptures become an excellent decoration for the garden. There are no limits to imagination here. You can create anything. All kinds of metal, concrete, and plaster parts are suitable for this. If you have a welding machine at hand, a pack of electrodes and, most importantly, a desire to create and create, then you can build an original composition that will take its rightful place on your site, making it more attractive.
Today, interesting design ideas for metal crafts can be found both in specialized publications and websites dedicated to decorating summer cottages, and you can come up with them yourself. In any case, do-it-yourself metal crafts, even those created according to an existing drawing, will be unique, because... Welding is, first and foremost, creativity. Any weld made by a certain person and executed with a certain decorative intent will be considered a kind of masterpiece. Therefore, get inspired, come up with and bring your ideas to life.

Many people have a desire to produce any product; beginners and experienced craftsmen create metal products with their own hands for sale. Some people come up with some pretty interesting developments.

What can you focus your attention on? How to start manufacturing products from steel and non-ferrous materials? What is in demand today? What products will be in demand in the near future? What tool should you have on hand? There are many questions. It's quite difficult to answer everything. But many potential entrepreneurs will still be concerned about finding their place in the market.

From idea to market

The peculiarities of the market are such that a very tiny product may be in demand, and large products, in which a lot of thought, work and talent have been invested, will turn out to be unnecessary. There are plenty of paradoxes in free trade.

Hardware is still in greatest demand.

Nails are bought in kilograms. They are used in construction, the manufacture of other goods, and in the production of packaging.
Self-tapping screws came to replace nails. Appearance cordless screwdrivers changed construction technologies and furniture production. It is much simpler and easier to assemble any spatial structure using self-tapping screws than to use disposable fasteners.
Screws (bolts) and nuts are fasteners that connect individual parts to each other. The demand is enormous. It is difficult to imagine any production that does not use threaded hardware.
Wire staples are used in conjunction with staplers. Mechanical, electrical and pneumatic staple driving devices are used in all walks of life. A small box of staples is available in any home. The goods do not sit on the shelves.
With the advent of tools for quickly connecting parts into finished products, blind and threaded rivets help in the production of complex one-piece units. The range of rivets is constantly expanding.
Welding electrodes represent a soft steel wire, coated with protective compounds. Even ordinary clay on the surface of wire rods allows parts to be welded together using electric arc welding.

To start producing hardware, it is enough to purchase automatic machines, for example, a nailing machine. All that remains is to thread the wire from the next roll into the machine and set it to right size nail. All further work proceeds without human intervention.

To operate the nailing machine, you will have to purchase wire and boxes in which to pack finished products. In the production of nails, one person performs the duties of director, accountant, foreman and auxiliary worker. Everything is in one hand. All that remains is to distribute the goods according to retail outlets and wait for results from its implementation.

The equipment for the production of other hardware is not much more complicated. In a small workshop and even in a garage, entrepreneurs organize completely modern mini-factories that produce in-demand goods.

Those who managed to establish the production of hardware in the early nineties of the last century still continue to produce them. Small factories export staples, nails, screws, screws, bolts and nuts to dozens of countries. Electrodes in trading network are purchased in tons.

What can an amateur manufacturer offer?

When it comes to metal products, then many potential manufacturers begin to fantasize about the manufacture of large spatial structures. Others see themselves as blacksmiths, forging intricate fences or steel flowers.

In fact, the list of metal products is quite extensive:

Jewelry production. It is not necessary to use precious metals and alloys to create a sought-after product. Most jewelers work with cupronickel, bronze, brass and copper. They decorate their works with pebbles collected from streams and rivers. Jewelry and decorations sell out quite well before major holidays.

Cold steel is an interesting line of work. The demand is constant. However, the manufacturer is always under close surveillance by law enforcement agencies. It is advisable to start making weapons to reconstruct historical events. There is no need for sharp sharpening, just similarity with the prototypes is enough.

The production of armor will be in demand in the coming decades. Many clubs are being formed where those who want to get involved in history are looking for manufacturers who can produce ammunition for medieval knights according to the given designs and height of the customer. The price of the products is quite high. Subject to High Quality demand is quite high.

Manufacturing metal structures for protected ground is quite promising direction activities. Greenhouses and greenhouses, made wisely, are always needed for summer cottages. Even raising livestock in chicken coops on a metal frame is more interesting than traditional methods. Rabbit cages from profile pipe, covered with panels, allow you to raise furry animals quite profitably.

Stairs for the home are most often made on the basis of a metal frame. The designs address different ideas for manufacturing staircases and railings. Having mastered the technology of calculation and welding, the master will receive a profession in demand for several decades. Individual construction is only gaining momentum. Entrance groups and interfloor stairs will be ordered constantly.

Metal furniture is in demand outdoors. Various types benches, benches and tables are used in parks, gardens, dachas and personal plots. These items, after being painted with protective paints, can be left outdoors. They are not afraid of precipitation, temperature changes and other natural disasters. The demand for such products is always stable, especially in spring and summer.

Metal gazebos are a rather interesting line of production. Prefabricated and welded structures do not require the use of complex technological equipment. Any craftsman who has mastered the features of using an angle grinder and a welding machine is able to independently weld structural elements. After painting, ready-made fragments are obtained; all that remains is to deliver them to the site and assemble them. The sheet material serves as a roof.

A steel swing can take its place near the house. It is based on a metal frame, as well as a swing installed in bearings. The device is simple and can be mastered by a skilled person.

Tools for carpentry and metalworking tools in demand. Many craftsmen require simple devices, which make it easier to manufacture: hives and components; facades for cabinet furniture; parts for various crafts - and many other things that home manufacturers use on a daily basis.
Rural residents and summer residents will buy gardening tools and tools if the products contain new ideas that reduce labor costs. Conventional rippers or uprooters will be purchased by those who have to work on the land.
Agricultural implements for walk-behind tractors and mini-tractors, which are used more than effective ways soil treatment will definitely be assessed and paid for by buyers.

To master the manufacture of a particular product, you can read the relevant books, watch videos and familiarize yourself with step by step guide on the main operations and the tools used.

How to start and grow a business?

You can hear the opinion that to create your own business empire you need significant initial capital. Without it, it is impossible to organize a profitable business. But history proves otherwise. With relatively small investments, gigantic fortunes and enormous production are created:

Henry Ford began building production with one successful engine on a self-running wheelchair. It cost only $50 to not only design and build the first engine from water pipes, as well as carts with steering and brakes. Already during his lifetime (1924), the company produced more than a million cars a year.
Dale Carnegie remained a teacher all his life, but managed to earn more than a billion dollars. He correctly decided on what he had to offer: he taught others how to make money. He earned money himself; his heirs could not count the inheritance for another twenty years.
Michael Rubin started his business at the age of ten, selling seeds. No initial capital. Then he organized the first snow removal company: he hired friends to work and agreed with the neighbors that within an hour there would not be a single snowdrift left near the houses. An enterprising boy at the age of 12 headed small company to restore order. At the age of 14 he had his own store. Today his fortune is estimated at more than $2 billion.
Sergey Brin came to the USA at the age of five and now heads GOOGLE. Anyone who wants to will always find the necessary information about him.

The main thing is not the presence of initial capital, it is important to desire and try to achieve the fulfillment of your desires. You need to put all your time into this and try to find ways for further development even in losses.

Eat certain rules, which should not be neglected. If you decide to deal with metal and products made from it, you need to decide on the place where it will be organized. manufacturing process. You will need tools, fixtures and raw materials.

At the initial stage, non-mass production is organized, they start with the first experimental models, on which demand is tested, the limit price of the proposed sample and the wishes of potential customers are determined.

It's time to consider some areas of activity.

Jewelry production

Optional precious metals in your work. Copper, bronze, brass and cupronickel look quite attractive. These metals can be cast into special molds to create original products.

Stable demand among buyers for products made by weaving. Various chains, brooches, necklaces and bracelets are jewelry in which openwork wire weaves create unique designs. Having mastered the complex technology of creating spatial structures, the master will acquire a circle of people willing to buy his products. In the future, a transition to the use of silver and gold as raw materials is possible.

Jewelry manufacturing technology using casting method

To familiarize yourself with the features, you need to look at the proposed photos and explanations for them.

For foundry on the table you will need:

A flask is a device into which blanks are cast. It creates a mold for future casting.
Container for preparing molding sand. It's mixed here different types gypsum and mixed with water.
Device for centrifugal casting. Most often, this is a special chain suspension that is untwisted to force the foundry mixture to fill the mold with a certain force.
Tool for grinding cast metals.
Gas burners - they are used to heat the flasks, molding mixtures and melt the metal.
Devices for making models. In the production of rings, cylindrical supports of different diameters are used.

For spatial and flat models, boards are used, on which the model mixture is placed and the model is cut out;

Sets of cutters - they are used to cut out the design of the future product.
Grinding tools for processing models and castings: files, needle files, sandpaper, drills and other abrasive tools.

To perform casting you need to have:

Foundry mixture - if there is copper and lead, then mixing them in different proportions, bronze is obtained. By mixing electrical copper and tin, brass is obtained. Old nickel silver products can become raw materials for the manufacture of silverware. Some craftsmen purchase brass fittings, cut them and cast their products;
Molding sand is a special product that uses fine sand mixed with gypsum. Ordinary building plaster will not work; the shape and size of the grains will not allow you to repeat a complex and small pattern;
Modeling wax is a plastic structure from which complex surfaces are cut. This material, slightly heated, can be glued in the right places. Beginning craftsmen use paraffin from candles. Simple models can be cut from cheap raw materials, but the quality will be low.

Information: Carl Faberge began production jewelry made of bronze. At first he cast medals and cigarette cases. Only after mastering the technology did he begin to use silver, gold, platinum and aluminum in his work.

Attention! When preparing foundry mixtures yourself using lead, tin, zinc, antimony and other heavy metals, you should have exhaust devices to remove vapors.

Step-by-step guide to making a brass ring

Attention! Lost wax casting technology. It received this name because after pouring the molding mixture and its hardening, the model wax is melted out. It doesn't stay inside at all.

There is also a method of casting using burnt models. In them, the model is made of polystyrene foam. When molten metal is poured, the model is burned out.

The work begins with preparing the wax mass. It is heated. At a temperature of 62…65 ⁰С the wax melts. Heat a little higher, to about 70 ⁰C, so that it remains in the molten state longer.

Wax is applied to the surface of a template of a certain diameter. A good craftsman usually has a set of templates so that he can make rings and rings for different clients. The minimum size is 12 mm and the maximum is 28 mm.

Subsequently, all work on preparing the model is carried out on the surface of the template. The wax is cut to the shape of the future product. A pattern is formed on the main surface.

If the stone needs to be secured in the future, small tendrils are created on the model. They will hold the stone on the front surface of the ring.

The template allows you to work without the master touching the wax with his hands. Therefore, there are no fingerprints left on the surface. Having a set of cutters, skilled craftsmen cut out a convex or concave design. This is how signet rings are made.

When developing the model, it is agreed upon with the customer. Then the exact product approved in the order will be manufactured. Sometimes a master makes not one, but several models. Subsequently, one or more are selected to be cast from metal. The work is quite complex, so this stage of work is negotiated and paid for separately. Each new model– this is a new product that the master spends time on.

Attention! You can design a product in 3D modeling programs and make a model using a 3D printer.

After all the elements of the future product have been worked out, the model is removed from the mandrel. A gating system needs to be manufactured. It will be needed for subsequent metal pouring. Ensure that there is sufficient volume for the melted mass. There should be plenty of it.

Ordinary plasticine is used as the basis for making a sprue. Filling is done through at least two holes. One is molded, and the second serves as a vent - air outlet. It is correct to place them at different heights. Thick wire is used to create holes.

The rods are slightly heated before installing the model. Then she sits down easier. They try to make the casting hole lower, and the projection a little higher. Its filling will occur with the reverse movement of the metal at the moment the space is filled.

The flask is put on the gating system. A tight installation will not allow the molding sand to leak.

Inside the flask you can see that the model does not touch the walls of the flask anywhere. There will be no deformation of the product when pouring.

The molding mixture is mixed with water. A solution is obtained that must be poured into the flask.

When pouring, it is advisable to place the investment ring on a vibrating table. Then air bubbles will be removed from the poured mass. The absence of bubbles will make it possible to obtain a durable shape without defects. It remains to wait until the gypsum present in the mold hardens.

The gating system is removed from the flask. Now the wires responsible for pouring the metal are visible.

Remove the wire. There will be access for metal through small holes. But for now there is a model inside. It is surrounded on all sides by the frozen molding mixture. When removing the wire, try to act carefully so as not to damage the workpiece.

After removing all the auxiliary elements, the mold begins to warm up and wax is removed from it. The flask is turned upside down. Place it on a dish where the wax will flow out.

When the wax comes out, a cavity is formed inside for the metal. Filling by centrifugal injection molding is provided. A special device in the form of a box and chain is used. The flask will have to be rotated by hand so that, under the influence of centrifugal force, the metal penetrates more fully into the most distant spaces of the form.

Heating is carried out in a device for centrifugal casting.

Attention! At home, other injection molding methods are also used. Many jewelers use potato halves. When there is molten metal, the flask is covered with a potato and pressed against the flask with force. From below heat over 800...900 ⁰С. Moisture evaporates from the surface of the potato. The resulting steam presses on the molten metal with its pressure. It penetrates into the most remote parts of the form.

When all free moisture has evaporated from the mold and a temperature close to the melting point of the metal being poured has been reached (about 850 ⁰C), pieces of brass (nickel silver, copper, bronze or other material) are placed on the sprue part.

The molten metal flows into the mold. Now you need to force it inside. They begin to unwind the device for centrifugal casting. Craftsmen using steam apply potatoes and wait for the steam to push the metal inside.

It doesn't take long to turn (about two minutes). The fluidity of the metal decreases quickly. You need to wait until the product hardens inside the mold. The temperature difference between the device and the surrounding air is high, so after 5...8 minutes the casting will become solid.

You can destroy the plaster and remove it from the flask by waiting for it to cool. This is what they do when casting gold products. If mold particles cool quickly, they can damage the soft metal.

In cold water, within a few seconds the mold will collapse and the product will be released. It's easy to get.

The casting shows the remains of the gating system. Use pliers to cut off the excess. They can be reused. When using expensive metal, use a jigsaw to saw through the sprues.

The immediately cast part looks unattractive. It is treated with sandpaper and polished. Give marketable condition. If necessary, the drawing is refined using pens, giving it an even greater convexity. Skilled craftsmen apply a fine mesh, which will enhance the texture effect.

The size is being finalized. After casting, it is possible to reduce the diameter of the ring. You can simply grind off the excess inside with files or needle files. More often they use mandrels (a tool made from hard material of a given size, for example, balls from a bearing), which are driven through the holes.

Using polishing wheels, the surface is processed and a high-quality product is obtained.

Products containing copper are treated with sulfur. It helps you see the depth of the drawing. The easiest way is to use sulfur ointment purchased at a pharmacy.

By firing at a temperature of 250...280 ⁰C, the oil evaporates. The sulfur film settles in the depressions. Excess on convex areas is removed by polishing using polishing pastes.

The finished metal product is examined for defects. If they are not there, then you can give them to the customer and receive payment for the completed order.

Video: decorative elements made of metal.

Other types of own production for profit

Studying step-by-step technologies, you can master several different professions in the manufacture of goods from metal.

The issues of individual production are quite interesting. For an active person, a direction will always be found, which in the future will become the work of life.

Every person strives to decorate their home. For this purpose, some buy various decorative items in stores, others make figures from scrap materials with their own hands. Made from wood, glass or metal, crafts occupy a worthy place in the home and attract with their originality.

Making metal decorative jewelry

Nowadays, many people make their own decorative elements. Why spend money on purchasing ready-made jewelry if you can make it yourself from scrap materials? Of course, working with metal requires certain skills and knowledge, so it is recommended to start by creating simple shapes.

To learn how to make crafts from metal, you will need to master the techniques of working with welding equipment. Welding is The best way fasten metal parts together. If you don't have a welding machine, you can purchase one from a hardware store or ask a neighbor. You will still need electrodes to work.

Material for your creations can be found in the garage among unnecessary spare parts and sheets of metal. Those who constantly create decorative jewelry from iron even visit landfills in search of suitable parts. Thanks to the hands of craftsmen, already obsolete designs acquire new life, embodied in beautiful figurines and sculptures. Moreover, such material is obtained completely free of charge.

Metal crafts

Iron is a durable material that is used in a huge number of structures. You can make many useful things from it, for example, a table and a bench for a summer house, a barbecue, a stove, as well as original figurines that will decorate the area. Today, landscape design, which can be supplemented with metal products, is very popular in country houses. Crafts of this kind look very harmonious on the site and evoke envious glances from neighbors.

With patience, you can bring to life the most bizarre design. You can make an iron beast or a man, a model of an airplane or a motorcycle. It all depends on your imagination. If you can’t come up with anything, you can look at ready-made metal crafts. Photos of some of them are presented in this article.

Basic safety rules

When working with metal and welding, safety precautions should be observed. You should not handle a sheet of iron without thick gloves. The material may have uneven and sharp edges that are easy to cut on.

When starting welding, be sure to wear a mask or safety glasses. In general, it is better to work in a special suit that will protect you from sparks flying in all directions. Do not cook near flammable materials: plastic, paper, wood.

From all of the above it follows that you can make decorative metal jewelry and crafts for your home and garden with your own hands. At the same time, you will not only save on your purchase finished product, but also enjoy your work.

fb.ru

What you can do with your own hands from old scrap metal

Even in ancient times, starting from the 11th century, it became a popular craft to make handicrafts with your own hands, from scrap metal or, as they were called then, metal rocks. Gradually, this craft turned into a real art, which is now an integral historical part of architecture and ancient buildings. You will be interested in seeing sculptures made from scrap metal with your own hands.

Today, there are many types of special tools that allow you to make sophisticated cuts on a metal surface, as well as weld or solder to connect several parts of non-ferrous or ferrous scrap. Modern technologies, give anyone the opportunity to make a product to their liking; for this it is not necessary to have any special artistic skills. All you need is desire and perseverance. Photos and videos of such handmade crafts can be seen on our website.

Be sure to check out - DIY crafts from waste!

DIY crafts have always been in demand and were quite valuable, as they emphasize the individuality and peculiarity of their owner.

Metal is one of the most durable materials; it can be used to create garden furniture or a children's swing, as well as small jewelry, such as a ring or bracelet.

For example, steel is much cheaper than gold or silver, but has greater strength; it, like precious metals, does not lose its color and does not corrode; many individual and original things can be made from it:

From a steel barrel, you can make a wood stove.

You can also make many useful and interesting things from waste car parts, for example,

the valves of an internal combustion engine will make excellent jingling bells for doors,

piston system and connecting rod mechanism, excellent table stand, it’s easy to make beautiful legs from them.

Environmental benefits

Scrap metal is thrown away every year and simply rots in the ground; instead, you can give it a second life by making some kind of craft, this is not only an interesting hobby, but also a way to protect the ecological system from hazardous elements, released during the decomposition of metal in the soil.

DIY metal products: features, types and drawings

IN modern conditions when the market is crowded with goods mass production, products are beginning to be in increasing demand self made. Specialized departments and entire shops or salons are beginning to appear in cities, selling exclusive items made by master craftsmen. If you want to give someone an unusual gift, the best option There will be metal products made with your own hands, although there are many other souvenirs in the hand-made style.

Handmade exclusive

Execution techniques can be so diverse that the range of products amazes even the most experienced person. Most often, such souvenirs are purchased for interior decoration or as a gift. You can buy or order the following items:

Products can be made using the following techniques:

It all depends on the imagination and technical equipment and skills of the authors. Among customers with large financial resources, metal art products are especially popular.

Areas of application

Items made using artistic casting and forging techniques are used to decorate elements in various areas of design:

Decorative items made of metal effectively complement any interior, giving it a certain chic and luxurious style.

Types of decorations

Do you want to learn how to make metal products with your own hands? Photos of such objects fascinate with their beauty. All things look very elegant, and most importantly, they retain the warmth of the author’s hands. That is why such products are quite expensive. True connoisseurs of style are willing to pay well for something exclusive.

You can make various metal products with your own hands. The following techniques are used to process this material:

The items that can be made using these methods are very diverse. Masters do:

Making metal products with your own hands is quite simple. The main thing is to know the stages of the process and have necessary equipment. Complex items require a lot of time and expensive equipment to produce, but some souvenirs can be made from almost nothing. It all depends on what you are going to do this for. If you choose artistic treatment metal as a field of professional activity, then you should be patient and realize that some financial investments will be required. For making simple but original gifts friends, relatives and acquaintances will only need desire and perseverance.

Manufacturing technologies

You can easily create metal products with your own hands. Photos of drawings and process stages will help you with this. Performance artwork involves stages of forming, processing and finishing. Making things, as already mentioned, occurs in different ways.

Casting refers to the filling of a mold with a liquid alloy.
Forging is the plastic processing of a material with a hammer, a press, as well as bending, twisting, and chopping.
Bending is a simple type of the previous option, performed by riveting or welding parts of the product.
Defeating is a method of processing a thin, no more than 2 mm, sheet of metal with hammer blows, thanks to which it acquires the required configuration.
Separate elements are prepared by stamping and cutting and holes are made.
Filigree is made from twisted or smooth, sometimes flattened copper, silver, and rarely gold wire. The curved parts of the patterns are soldered.
When minting, a relief pattern is obtained using stamps or special tools that are placed between the hammer and the product.

Drawings of metal products can be done manually or in special programs on a computer. Three-dimensional modeling allows you to make not only a regular drawing, but also to build a three-dimensional model of the future product. It makes it possible to see appearance things, including in the interior, long before its actual appearance. In this case, it is possible to adjust the product parameters without material costs for its re-production.

How to make a box from an aluminum can

Even a schoolchild can make the most basic metal thing. The main thing is that this will require practically nothing except time, hard work, imagination and the desire to create. You can make a beautiful box from an ordinary soda can.

Materials and equipment

The raw materials for production, one might say, are lying under your feet on the street. You will also need the following items:

sandpaper (skin);
sharp scissors;
ruler;
pencil;
ball pen;
solid base no larger than A4 format (depending on the size of the box);
sheet of paper for the diagram.

Sequencing

At the first stage, a layer of paint is removed from the can using sandpaper. It is better to do this from an unopened container, since its walls remain elastic under the influence of the contents. The process will go faster and you won't ruin the metal. If you use an empty one, be careful not to crush the can.

In the next step, you need to obtain a thin sheet of aluminum from the blank, the size of the reamer of the future box.

To do this, the can is cut.
Sharp and uneven edges are removed.

At the next stage, the edges and sides of the product are marked.

A thin metal sheet is placed on a solid base.

The diagram of the box can be drawn directly on a metal sheet.

Or you can trace a sketch made in advance on paper.

When the layout of the box is ready, we proceed directly to drawing the drawing. This is done using a ballpoint pen or a sharpened pencil. Please note that you will have to trace the patterns several times on both sides. This will make the design more decorative and convex.

You yourself were able to see that it is very easy to make products from thin sheet metal. You may well be able to try your hand at this. You can make not only boxes in this way, but anything that comes to mind.

How to turn a hobby into a small business

Making such exclusive gifts can also be a profitable business. You can sell crafts through advertisements or recommendations from friends. If there is a salon in your city that accepts souvenirs, you can donate them there. It is quite profitable today to create metal products with your own hands. They can be put up for sale on many specialized websites. Such online sites are easy to find. The “Masters Fair” works well, but you can use other services.

How to sell your crafts online

If you decide to opt for online trading, then take into account that the operating principle of all stores is the same:

You register as a craftsman who sells items.
Fill out your profile.
Exhibit your work.
You come to an agreement with the customer.
He pays for the goods.
You deliver.

There you can display both finished items and take orders. It is very important to choose the right product category, come up with its description, select high quality image. Be sure to write a caption for the photo and indicate that you make metal products with your own hands. We accept exclusive items for sale that can easily be sent by courier or by mail to the customer. Items should not contain very thin or fragile items that could break during transportation. If such parts are available, you must provide high-quality packaging so that the product reaches the client in its original form. After all, every mistake can significantly affect your image. Try to complete all decorative metal products with high quality and on time. Good feedback customers play an important role in this line of business. This way you can turn your favorite activity into a source of income.

Finally

So, as you understand, it is quite easy to make metal products with your own hands. This type of activity would be an excellent hobby option. Also, your friends and family will be the happy owners of exclusive gifts. In addition, by offering samples for sale, you will create an image of a good craftsman and be able to make a profit.

fb.ru

Crafts from scrap metal

From what's lying under the welding table. Please do not judge too much for the clumsiness, but because... there is no grinder, no milling machine, made using a grinder, electric welding, a file (when I was not too lazy))), and a cutter.

Moreover, it was done during lunch breaks, and when you are late...)))

I'll start with small things like cold stuff. From the bearing race. Hardening and tempering are done in a smart way, you can shave.))) I tempered it in an oven for calcining the electrodes.

Full size. Spring, bearing race. The pistol on the right is a working scarecrow gun with primers. At first I made it with construction cartridges, but it really hurt my ears...))) Kholodnyak (large) was forged and hardened in a forge.

Full size MG. Everything works until the drummer clicks. I did it for a week (if you count a couple of hours a day). Not working sights (in the sense of not moving). And the cupcake does not open (why, there are no cartridges anyway)))).

Every owner spends a lot of time thinking about how to decorate their home. Today there is a huge choice of materials - wood or plastic, but in the first place is metal - one of the durable, strong, resistant materials in the world, serving as an example and standard of metaphors.

History of origin

Metal products became most popular in Europe in the 11th century. Everywhere, facades of buildings, fences, and decorative statues began to be decorated with unusual forging, and the profession of a blacksmith became an honorable and famous figure in the early Middle Ages.

What kind of craft can be made from metal?

Having thought carefully, the owner decides to present a piece of the unusual to his home, but the question immediately arises: should he buy it or make it himself? Of course, do it yourself, because doing something with your own hands is much more pleasant and more profitable from a price point of view.

Today, forged ornaments for grilles, doors or fences are in fashion; forged animals, a mysterious owl, or a Russian bear also look great in the garden. Ladies prefer forged bouquets, and a rose created with their own hands will surprise anyone.

What do you need to make metal crafts?

There are not as many tools as it seems, all you need is the following list:

Photo of a craft you like;
Paper;
Welding machine;
Chisel and hammer;
Grinder for cutting metal;
Special rust solvent;
Pencil and scissors, when using a stencil;
Several washers or bolts for decorative elements;
Steel rods, from a few centimeters to a meter.
The basis of creation is sheet iron.

Step-by-step DIY crafts

An original idea for a metal craft would be an owl. First, for aesthetics you will need a template or stencil. It can be made from a sheet of paper with drawings printed on it.

After cutting out the owl drawing, the stencil should be applied to a sheet of steel and the drawing should be transferred; it should be done in the most realistic way.

The next step is to trim the metal with a grinder and drill holes for mounting and inserting the owl's eyes. After creating the body, you should move on to the details: the legs are made from a rod, and the irregularities are smoothed out with a grinder. At the end, our beauty is treated with a chemical rust remover and painted.

Master class on making roses

And materials. List of basic tools:

Attention. Do not forget about safety precautions when working with these tools! Be sure to wear gloves and a welding mask when working.

We take metal cutting scissors and cut out thirty rose petals (thirty petals will make the bud seem more magnificent). You need to move in cutting from small to large, that is, from 15 mm to 80 mm. Your rose should not be prickly. Therefore, a sharpening stone will help smooth out all the unevenness of the petals.

After forming a complete flower, we weld the spikes and clean off the excess with a grinder, clean the seams and cover with a layer of protective paint - the craft is ready.

Metal products with steel wire

The British National Academy of Sciences declared in 1856: “Everything that can be invented has long since been invented,” but time has shown a different outcome. So it is now. Every year new ways of decorating are invented.

For example in last years It is fashionable to make a figure from wire or rod. Combinations and special weaves create an impression of indescribable beauty.

Master class - butterfly made of twig

In terms of its complexity, a steel butterfly is not difficult and will not take much time. Typically, the work technique consists of twisting the wire (the manufacturing process depends on the correct material: the material should not be too thick so that it can bend, but should not be too thin so as not to bend) into several layers.

A body is created using spiral turns, after which wings made from two ovals are attached.

Some interesting facts

Metal is the most ancient mineral of interest to humans. He mined it, forged it, and then a new fence or another forged deer lit up the smile of passers-by.

During the rapid introduction of Hollywood films and development artificial intelligence, the topic of androids and the like has become relevant. Although the world is far from the rise of the machines, it is always possible to forge a transformer, say, for an exhibition.

Vitaly Yashkovich from Krasnoyarsk became famous throughout the city for his miracle robots. His collection includes such titans of world cinema as: Megatron, Terminator T-200 and T-800, androids star wars, as well as droids from cartoons. The owner himself claims that he will not sell his robots to anyone, they say, he created for the soul

You too create, because the world is unidentified and multifaceted. Give him something new and unusual.